pylabrobot.formulatrix package#

Mantis#

Mantis

A Formulatrix Mantis, v3 or v4.

MantisDevice

A Formulatrix Mantis, v3 or v4: its main box, the parts on it and the driver that runs it.

MantisCarousel

Home and position an LC3 carousel independently of the Mantis arm.

CarouselConfiguration

One LC3 and its fitted carousel; angles in degrees, speeds in degrees/s.

driver.master.MantisDriver

Talks to a Mantis: one command in flight, events logged as they come.

driver.simulator.MantisSimulationDriver

A Mantis driver with no device behind it.

driver.simulator.MantisSimulationArm

An arm with no device behind it: each command sets where its motors are, at once.

driver.simulator.MantisSimulationPlateClamp

A plate clamp with no device behind it: each command sets the state it ends in, at once; a valve on a pressure-board output switches at once.

driver.simulator.MantisSimulationPump

A pump with no device behind it, answering from the declared configuration.

driver.simulator.MantisSimulationRfid

An RFID reader with no device behind it: every slot reads empty.

driver.simulator.MantisSimulationLedBar

An LED bar with no device behind it: every command is taken, and no hold is waited.

driver.features.arm.Arm

The arm and Z, built on every unit; the generation selects only private plumbing.

driver.features.arm.MantisPose

Where every joint of the arm is and where the nozzle is, in the deck frame, mm.

driver.features.arm.MantisArmConfiguration

The arm's facts, read at setup, and the unit's calibration, from its folder or declared file.

driver.arm_kinematics

The arm's kinematics and units: pure maths, nothing sent.

driver.stage_transform

The stage transform: where a point on the wellplate is in the arm frame.

driver.sequence_files

A unit's sequence files (.seq.txt): one item per line, its class name first.

driver.features.plate_clamp.PlateClamp

The plate clamp, on board 12 or on a pressure-board output, with the same methods.

driver.features.pump.Pump

The pump and the pressure controllers, built when the pressure board answers.

driver.features.rfid.Rfid

The RFID reader.

driver.features.led_bar.LedBar

The v4's LED bar: number_of_leds LEDs, each showing one RGB565 colour, or an animation.

driver.configuration.DeviceConfiguration

What the device reported about itself.

driver.events

The events a Mantis sends unasked, and what each carries.

driver.errors.MantisError

Any Mantis error.

driver.errors.FrameError

A frame from the device is malformed.

driver.errors.ChecksumError

A frame's check word does not match its bytes.

driver.errors.MantisNotConnectedError

A command needs the link, but setup has not run or stop has.

driver.errors.MantisConnectionLostError

Reading a link failed; the failure is the cause.

driver.errors.MantisTimeoutError

The device did not answer, or did not reach a state, in time.

driver.errors.MantisConfigurationError

A declared configuration disagrees with the device, lacks a value, or names an unknown slot.

driver.errors.PlateClampError

The plate clamp reported a failure or did not reach the commanded control state.

driver.errors.MantisMotionError

A motor reported a fault or did not reach a commanded state.

driver.errors.MantisPressureError

A pressure controller did not reach its target, or a sensor raised an alarm.

driver.errors.InvalidQueueItemError

A sequencer queue command answered a non-zero error field.

driver.errors.MantisKinematicsError

A target position is out of the arm's reach or at a singularity.

driver.errors.MantisCoordinateError

A container cannot be mapped to a device position.

driver.errors.MantisPrimeError

A prime ran its full volume, but the liquid sensor never confirmed flow.

resource_model.chip_rack

A chip rack, fitted on one side of the deck, with a chip spot for each of its input slots, named {name}_spot_{slot}.

resource_model.z_column

The Z column, which carries the arm.

resource_model.arm_link

One of the arm's four links.

liquid_classes.MantisLiquidClass

Dispense tuning for one viscosity band on one chip type.